Bearing is bad fast, install the disaster that cause

1.Scroll bearing service instruction

(1) force of the merit when installing bearing is even, cannot direct hammer is attacked. Be like: Had cooperated to be filled with bigger, answer to put bearing in accusing lukewarm air heating furnace or oily furnace automatically to heat, heat strict control is in temperature 120 ° are the following.

(2) can be in of the bearing of nylon cage - 40 ° - long-term and successive stability works below 120 ° , when 150 ° the job should not exceed 4 hours, brief temperature peak value can amount to 180 ° .

(3) the storeroom Ying Qingjie that deposits bearing, dry forbid to be the same as with chemical product store one library, relative humidity should not exceed 65% , and bearing forbids be born to store.

Bearing is bad fast, install the disaster that cause

2.Installation of deep trench ball bearing is used

(1) force of the merit when installing bearing is even, cannot direct hammer is attacked. Be like: Had cooperated to be filled with bigger, answer to put bearing in accusing lukewarm air heating furnace or oily furnace automatically to heat, heat strict control is in temperature 120 ° are the following.

(2) can be in of the bearing of nylon cage - 40 ° - long-term and successive stability works below 120 ° , when 150 ° the job should not exceed 4 hours, brief temperature peak value should not exceed 180 ° .

(3) the storeroom Ying Qingjie that deposits bearing, dry forbid to be the same as with chemical product store one library, relative humidity should not exceed 65% , and bearing forbids be born to store.

(4) inventory bearing every other should be cleaned one year afresh, undertake antirust pack.

3.Horn contacts ball bearing installation to use

(1) force of the merit when installing bearing is even, cannot direct hammer is attacked. Be like: Had cooperated to be filled with bigger, answer to put bearing in accusing lukewarm air heating furnace or oily furnace automatically to heat, heat strict control is in temperature 100 ° are the following.

(2) can be in of the bearing of nylon cage - 40 ° - long-term and successive stability works below 120 ° , when 150 ° the job should not exceed 4 hours, brief temperature peak value can amount to 180 ° .

(3) the storeroom Ying Qingjie that deposits bearing, dry forbid to be the same as with chemical product store one library, relative humidity should not exceed 65% , and bearing forbids be born to store.

4.Installation of bearing of the roller that move a heart is used

(1) the user should cooperate the interest with bearing suitably by use requirement choice to windage. Bearing code name is proofreaded first please after tearing open a bag.

Before bearing is installed, when if need to be inside bearing,lubricating grease, grease must clean, right amount.

(2) attack with not direct hammer when installation inside, outer lane end panel and roller are advisable, lest attack,crack inner ring or in, small rib. Normally the user should put bearing 90 ° heat inside mineral oil - when 100 ° instantly mount main shaft. Avoid by all means uses local gush to burn a law to bearing, in hard " shrinkage fitting " when the user also should be installed with special sleeve.

(3) bearing is used in due and good sealed and dustproof fit and lubricant, cannot break oil.

(4) bearing storeroom Ying Qingjie is dry, without environmental pollution, bearing piles up not be born, pack without damaged. The bearing that inventory exceeds 1 year must be cleaned afresh oiled.

5.Thrust moves installation of heart roller bearing to use

(1) a bearing oil seal answers when installing bearing abluent again the clean excellent lubricant on besmear.

(2) when installing bearing, merit force is even, cannot hammer is attacked. If had cooperated to be filled with bigger, should put bearing 90 ° heat inside mineral oil - after 100 ° , install instantly.

(3) the storeroom Ying Qingjie that deposits bearing, clean, relative humidity does not exceed 65% .

(4) inventory bearing every other should be cleaned one year afresh oiled, oil seal is packed keep good.

(5) when use bearing, due and good sealed and dustproof fit, answer to often examine working case.

6.Installation of columnar roller bearing is used

(1) this bearing is depart model, the user installs Shi Kegen to adjust windage according to needing proper motion.

(2) before bearing is being used, applied benzine or kerosene are cleaned clean, keep good and lubricant.

(3) when bearing is installed, should control bearing the part inside, forbidden beat.

(4) bearing deposits place Ying Qingjie ventilated, avoid moisture, need the bearing that keeps for a long time, should fixed and antirust.

7.Installation of thrust ball bearing is used

(1) bearing should be demolished to seal when installing bearing, abluent besmear again the excellent lubricant that goes up clean.

(2) when installing bearing, merit force is even, cannot hammer is attacked. If had cooperated to be filled with bigger, should put bearing 90 ° heat inside mineral oil - after 100 ° , install instantly.

(3) the storeroom Ying Qingjie that deposits bearing, clean, relative humidity does not exceed 65% .

(4) inventory bearing every other should be cleaned one year afresh oiled, oil seal is packed keep good.

(5) when use bearing, due and good sealed and dustproof fit, answer to often examine working case.

未经允许不得转载:News » Bearing is bad fast, install the disaster that cause